Womens T-Shirts Polyester Sublimation Blank

♨️ Sublimation Instructions for Womens T-Shirts Polyester

_x000D_

📋 Materials Needed

_x000D_

_x000D_
• Sublimation printer and sublimation ink

_x000D_

• Sublimation paper

_x000D_

• Heat-resistant tape

_x000D_

• Flat Heat Press

_x000D_

• Womens T-Shirts Polyester (Substrate)

_x000D_

• Lint brush<!-Needed1End–>

_x000D_

• Pressing pillow<!-Needed2End–>

_x000D_

_x000D_
_x000D_

_x000D_
_x000D_
_x000D_

🔥 Flat Heat Press Settings

_x000D_
Temperature: 180–200°C_x000D_
Time: 60–80 seconds_x000D_
Pressure: High_x000D_
_x000D_
(Tip: Different presses vary—start at 190°C for 70 seconds and adjust if needed.)_x000D_
_x000D_
_x000D_
_x000D_

_x000D_
_x000D_

📝 Preparation

_x000D_

_x000D_
1. For templates, Mock-ups and image size required, please refer to the Design tab.

_x000D_

2. Print your design, MIRROR your image.

_x000D_

3. Clean the substrate printing surface using a microfiber cloth or lint brush to remove dust, oils or lint. (As per substrate)

_x000D_

4. Place the substrate sublimation printable area facing up, align the print to cover the area.

_x000D_

5. Secure the edges using heat-resistant tape to prevent movement.

_x000D_

_x000D_
_x000D_

_x000D_
_x000D_
_x000D_

🛠️ Flat Heat Press Pressing

_x000D_

_x000D_
1. Place a sheet of protective paper on the press.

_x000D_

2. If this is your first press of the day, make sure you do a pre-press at the suggested heat press settings and bring all materials up to temperature.

_x000D_

3. Flip the substrate holding the taped areas to secure.

_x000D_

4. Place the substrate into the press sublimation coating face up, towards the heating element.

_x000D_

5. Cover with another sheet of protective paper.

_x000D_

6. Press at listed Heat Press Settings Above.

_x000D_

_x000D_
_x000D_
_x000D_

_x000D_
_x000D_

❄️ Cooling and Assembly

_x000D_

_x000D_
1. Carefully remove the substrate from the press (it will be hot).

_x000D_

2. Peel off the sublimation paper while the substrate is warm for best results.

_x000D_

3. Allow the substrate to cool completely.

_x000D_

_x000D_
_x000D_

_x000D_
_x000D_

✅ Tips for Best Results

_x000D_

_x000D_
• Ensure full edge-to-edge coverage in your design to avoid white borders (ensure bleed is sufficient).

_x000D_

• If colours look dull, increase time by 5 seconds or pressure slightly.

_x000D_

• If the coating looks yellowed, your temperature is too high or time too long.

_x000D_

• Store substrate in a clean, dry, dust-free area before printing.

_x000D_

• If you use a pressing pillow that is greater than the size of the image and the paper is larger than the pressing pillow, you will not get any paper border lines.

_x000D_

• If you see small black marks, this is burnt lint (pay more attention to lint brushing).

_x000D_

• If you do not use a pressing pillow imagery can transfer through to the other side of the substrate.

_x000D_

_x000D_